Wavetronix SmartSensor Matrix (SS-225) - User Guide Manuel d'utilisateur Page 73
- Page / 117
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
72 CHAPTER 7 LANES & STOP BARS
Saving the Configuration
Aer automatic and manual conguration is complete, click the Save Cong button to save
the changes to the sensor. If you attempt to leave the Lanes & Stop Bar view before saving
your changes, the following prompt will appear (see Figure 7.8).
Figure 7.8 – Save Changes Dialog
Moving the Sensor View
e SSMM soware shows the position of the SmartSensor Matrix and the view is drawn
from the perspective of the sensor. If the perspective in the soware does not match your
perspective of the roadway, click the Rotate View button until the sensor position matches
the approach you are conguring.
Note
Moving the sensor in the software will have no eect on the sensor’s performance.
Its purpose is to facilitate the configuration process.
Restarting Auto Lane Config/Rebooting the Sensor
Restarting the automatic lane conguration will erase any auto-conguration information
that may have been gathered and will start the auto-conguration process over again.
Rebooting the sensor will also erase any auto-conguration information, but in addition
will clear and recongure the sensor thresholds.
Follow the steps below to restart the automatic lane conguration process or reboot the
sensor:
1 Click the Restart/Reboot button and the Restart or Reboot window will appear (see
Figure 7.9).
2 Select the appropriate radio button and click OK.
- SmartSensor Matrix 1
- Contents 4
- Introduction 6
- SmartSensor Matrix Package 7
- Selecting a Mounting Location 8
- Sensor Pole 9
- Figure I.3 – Corner Radar 9
- Installing the 12
- In this chapter 14
- Sensor Mounting Guidelines 15
- Front edge of field of view 18
- Grounding the Sensor 20
- Cabinet Solutions 2 22
- Click 650 23
- Click 600 24
- Preassembled Backplate 25
- Wire Color Signal 28
- Channel 31
- Bus 1 Bus 2 31
- Click 112 DIP Switch Settings 32
- Click 112/114 LEDs 35
- Click 104 LEDs 37
- Channel Mapping 38
- Using SmartSensor 42
- Manager Matrix 42
- Installing SmartSensor 44
- Manager Matrix 4 44
- Using the Click 650 45
- Using the Click 600 45
- Using the Click 421 46
- Microsoft .NET Framework 48
- Communication 5 50
- Serial Connection 52
- Internet Connection 54
- Address Book 56
- Virtual Connection 57
- Virtual Sensor File 58
- Communication Error Log 59
- Figure 5.10 – Error Log 60
- Sensor Settings 6 64
- Ports Tab 65
- Figure 6.2 – Comm Tab 66
- Advanced Tab 67
- Lanes & Stop Bars 7 68
- Edit Area 69
- Saved Configuration Overlay 70
- Capturing Lanes and Stop Bars 71
- Menu Bar 72
- Saving the Configuration 73
- Moving the Sensor View 73
- Editing Thresholds 74
- Automatic Configuration 75
- Adding/Deleting/Moving a Lane 76
- Moving a Lane Node 78
- Changing the Lane Arrows 79
- Zones & Channels 8 80
- Placing Zones 82
- Editing Zones 83
- Placing AutoZones 83
- Channel Type 84
- Mapping Zones to Channels 85
- Editing Channels 86
- Output Settings 87
- Measuring Zones 88
- Figure 8.15 – Using Flags 89
- Verification 9 90
- Channel Indicators 91
- Verification Menu Bar 92
- Tools 10 94
- Backup-Restore 95
- Sensor Diagnostics 96
- Tracker Logging 96
- 96 CHAPTER 10 TOOLS 97
- Figure 10.6 – Log File 97
- Using the Rack Card Tool 98
- Firmware Version 99
- Signal Cards Switch 99
- Channel Outputs Switch 100
- Appendix 102
- Creating Custom Cables 103
- Appendix B – Cable Lengths 104
- 104 APPENDIX 105
- Figure C.1 – Click 221 105
- Mounting the Backplate 106
- Connecting AC Power 106
- 106 APPENDIX 107
- APPENDIX 107 108
- 110 APPENDIX 111
- Angle Resolution 112
- 112 APPENDIX 113
- Occlusion 114
- 114 APPENDIX 115
- APPENDIX 115 116
- 116 APPENDIX 117
Genius 31100033101 Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Grafiktabletts Genius 31100033101.
Wir stellen 1 PDF-Handbücher Genius 31100033101 zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Datenblatt
Commentaires sur ces manuels