Wavetronix Command Collector (CMD-DCx) - User Guide Manuel d'utilisateur Page 58
- Page / 117
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
CHAPTER 5 SENSOR CONFIGURATION PAGE 57
the job will repeat. e Weeks and Months tabs also allow you to set collection to occur on
certain days or during certain months. Once you’ve set the interval, click the Add button
and the new collection interval will appear beneath the box.
Figure 5.8 – Advanced Tab
Attach to Multi-drop Server (if available) – Causes Collector to assign this sensor,
along with any other sensor that has the same IP/port and has this setting checked, to
a multi-drop collection group. For multi-drop–capable sensors on a common IP/port,
Collector supports optimized multi-drop communication for a set of sensors with a
common communication gateway.
e following is a list of important notes about multi-drop collection:
Sensors assigned to the same multi-drop server for collection MUST have the same
collection interval, even if the individual sensor intervals are dierent.
If a multi-drop server group using this IP/port already exists when a sensor is added, its
collection interval will automatically be changed to the group value. If no other sensors
are currently set to be collected via multi-drop, this sensor will become the start of a
new group, and will use the sensor’s current collection interval as the group collection
interval; future sensors added to the group will have their collection intervals changed
to this value.
A sensor does NOT need to have multi-drop collection enabled even if it shares an IP/
port with other sensors. Multi-drop collection must be disabled if a dierent collec-
tion interval is required for a sensor. Each sensor that is NOT enabled for multi-drop
communication with the same IP/port combination as other sensors will be competing
with those sensors for a common connection. If one Collector collection thread is us-
ing a connection, other competing threads will have to wait until the communication
pathway is open before continuing.
Proper multi-drop data collection requires the use of a driver that specically supports
multi-drop capable sensors. If the current sensor driver is incapable of supporting
multi-drop communication, enabling multi-drop data collection for this sensor will
result in data collection errors.
- Command Collector 1
- Contents 4
- Chapter 8 Help Page 103 5
- Introduction 6
- Data Storage 7
- Installing Command HQ 1 8
- Wavetronix representative 10
- Install button 12
- Command Licensing 13
- Oine Activation 14
- In this chapter 18
- Logging In 18
- Service Not Started Errors 19
- Common Web Interface Features 20
- Navigation/Status Control 21
- Web Interface Context Help 22
- Sensors Page 3 24
- Sensor List 25
- Network(s) 27
- Location 28
- Description 28
- Interval (Intrvl) 28
- Frequency (Fq) 28
- Figure 3.5 – Paging Control 29
- Display Settings Control 30
- Filter Controls 31
- With Com Status 32
- With Data Status 32
- Figure 3.10 – By Data Filter 33
- Sensor Toolbar 4 34
- Add Sensors 35
- Modem Support Using COM Ports 37
- Adding Ranges of Sensors 37
- Adding from an Address Book 38
- Remove Sensors 39
- View Errors 39
- Sensor Error Display Settings 40
- Sensor Error Queries 41
- Exporting Sensor Errors 41
- Collection 43
- Intervals 43
- Commands 45
- Networks 46
- Figure 4.18 – Search Box 48
- Figure 4.19 – Search Results 48
- Sensor Configuration Page 5 50
- Sensor Info Bar 51
- Com Status 52
- Data Status 52
- Communication Status Graph 52
- Data Status Graph 53
- Sensor Information 54
- View Log Button 54
- Sensor Config Tab 55
- Custom Configuration Panel 56
- Figure 5.7 – Basic Tab 57
- Figure 5.8 – Advanced Tab 58
- Lanes/Approaches Tab 59
- Setting Custom Lane IDs 60
- Approaches 60
- Sensor Commands Tab 61
- Data Query Tab 63
- Data Query Graphs 64
- Data Query Tables 65
- Data Page 6 68
- Selecting Sensors 69
- Define and Request Report 69
- Output Report Type 70
- 70 CHAPTER 6 DATA PAGE 71
- CHAPTER 6 DATA PAGE 71 72
- Figure 6.6 – Monthly Report 72
- 72 CHAPTER 6 DATA PAGE 73
- CHAPTER 6 DATA PAGE 73 74
- Saving a Report Template 75
- Export Tab 76
- Automated Custom Export 77
- Current Automated Export 78
- 78 CHAPTER 6 DATA PAGE 79
- CHAPTER 6 DATA PAGE 79 80
- System Page 7 82
- Status Tab 83
- Networks Tab 83
- Error Log Tab 84
- Figure 7.4 – Error Log Tab 85
- 84 CHAPTER 7 SYSTEM PAGE 85
- Users Tab 86
- Network Permissions 87
- User Privileges 87
- Settings Tab 88
- Information 89
- Mail Settings 89
- Status Settings 90
- 90 CHAPTER 7 SYSTEM PAGE 91
- Figure 7.9 – Status Settings 91
- Timer Settings 92
- Data Settings 93
- Collection Settings 94
- Database Settings 95
- Log Level 95
- Session Timeout 95
- Classes Tab 96
- Notifications Tab 97
- Journal Tab 98
- Service Tab 99
- Support Tab 101
- Figure 7.20 – Support Tab 102
- Help Page 8 104
- User Guide Tab 105
- License Info Tab 105
- License Agreement Tab 106
- Figure 8.6 – Support Tab 107
- 106 CHAPTER 8 HELP PAGE 107
- Driver Reference 9 108
- Custom Fields 110
- 3M 940 Trac Monitoring Card 111
- EIS RTMS X2/X3 112
- Autoscope 113
- Mikros Data Logger 114
- Class Mappings 115
Produits connexes et manuels pour Logiciel Wavetronix Command Collector (CMD-DCx) - User Guide
(4 pages)Genius 31100035101 Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Grafiktabletts Genius 31100035101.
Wir stellen 1 PDF-Handbücher Genius 31100035101 zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Datenblatt
Commentaires sur ces manuels