Wavetronix Command Collector (CMD-DCx) - User Guide Manuel d'utilisateur Page 93
- Page / 117
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
92 CHAPTER 7 SYSTEM PAGE
Note
Collector will not change the sensor’s clock unless the dierence is greater than five
seconds.
Enable Auto Time Synchronization – Causes Collector to frequently check for devices
with clocks that are more than ve minutes o.
Note
Continually running jobs to synchronize the sensor clock can have unintended
consequences. Some sensors will not create a data interval unless it can create a
complete interval. For example, if a sensor is set to five-minute bins, and it’s in the
middle of a five-minute period when the clock changes, then it will not complete
that bin and can cause data holes to occur. To help minimize this, it is recommended
to not run time sync jobs too frequently and to use a time server to keep the Collec-
tor server’s clock aligned.
Data Settings
e Data Settings box contains settings for data collection and aggregation within Collec-
tor (see Figure 7.11). You can congure Collector to store and/or display data in English
or metric units. Selecting Sensor Units from the Store Data In drop-down list will store
incoming data in whatever units the sensor reports in.
Figure 7.11 – Data Settings
e four aggregation radio buttons allow system administrators to disable aggregation or
toggle automatic data aggregation in 5-, 15-, or 60-minute intervals. Collector will retrieve
- Command Collector 1
- Contents 4
- Chapter 8 Help Page 103 5
- Introduction 6
- Data Storage 7
- Installing Command HQ 1 8
- Wavetronix representative 10
- Install button 12
- Command Licensing 13
- Oine Activation 14
- In this chapter 18
- Logging In 18
- Service Not Started Errors 19
- Common Web Interface Features 20
- Navigation/Status Control 21
- Web Interface Context Help 22
- Sensors Page 3 24
- Sensor List 25
- Network(s) 27
- Location 28
- Description 28
- Interval (Intrvl) 28
- Frequency (Fq) 28
- Figure 3.5 – Paging Control 29
- Display Settings Control 30
- Filter Controls 31
- With Com Status 32
- With Data Status 32
- Figure 3.10 – By Data Filter 33
- Sensor Toolbar 4 34
- Add Sensors 35
- Modem Support Using COM Ports 37
- Adding Ranges of Sensors 37
- Adding from an Address Book 38
- Remove Sensors 39
- View Errors 39
- Sensor Error Display Settings 40
- Sensor Error Queries 41
- Exporting Sensor Errors 41
- Collection 43
- Intervals 43
- Commands 45
- Networks 46
- Figure 4.18 – Search Box 48
- Figure 4.19 – Search Results 48
- Sensor Configuration Page 5 50
- Sensor Info Bar 51
- Com Status 52
- Data Status 52
- Communication Status Graph 52
- Data Status Graph 53
- Sensor Information 54
- View Log Button 54
- Sensor Config Tab 55
- Custom Configuration Panel 56
- Figure 5.7 – Basic Tab 57
- Figure 5.8 – Advanced Tab 58
- Lanes/Approaches Tab 59
- Setting Custom Lane IDs 60
- Approaches 60
- Sensor Commands Tab 61
- Data Query Tab 63
- Data Query Graphs 64
- Data Query Tables 65
- Data Page 6 68
- Selecting Sensors 69
- Define and Request Report 69
- Output Report Type 70
- 70 CHAPTER 6 DATA PAGE 71
- CHAPTER 6 DATA PAGE 71 72
- Figure 6.6 – Monthly Report 72
- 72 CHAPTER 6 DATA PAGE 73
- CHAPTER 6 DATA PAGE 73 74
- Saving a Report Template 75
- Export Tab 76
- Automated Custom Export 77
- Current Automated Export 78
- 78 CHAPTER 6 DATA PAGE 79
- CHAPTER 6 DATA PAGE 79 80
- System Page 7 82
- Status Tab 83
- Networks Tab 83
- Error Log Tab 84
- Figure 7.4 – Error Log Tab 85
- 84 CHAPTER 7 SYSTEM PAGE 85
- Users Tab 86
- Network Permissions 87
- User Privileges 87
- Settings Tab 88
- Information 89
- Mail Settings 89
- Status Settings 90
- 90 CHAPTER 7 SYSTEM PAGE 91
- Figure 7.9 – Status Settings 91
- Timer Settings 92
- Data Settings 93
- Collection Settings 94
- Database Settings 95
- Log Level 95
- Session Timeout 95
- Classes Tab 96
- Notifications Tab 97
- Journal Tab 98
- Service Tab 99
- Support Tab 101
- Figure 7.20 – Support Tab 102
- Help Page 8 104
- User Guide Tab 105
- License Info Tab 105
- License Agreement Tab 106
- Figure 8.6 – Support Tab 107
- 106 CHAPTER 8 HELP PAGE 107
- Driver Reference 9 108
- Custom Fields 110
- 3M 940 Trac Monitoring Card 111
- EIS RTMS X2/X3 112
- Autoscope 113
- Mikros Data Logger 114
- Class Mappings 115
Produits connexes et manuels pour Logiciel Wavetronix Command Collector (CMD-DCx) - User Guide
(4 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.033 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels