Wavetronix SmartSensor Advance Extended Range (SS-200E) - Use Manuel d'utilisateur Page 63
- Page / 148
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
62 CHAPTER 6 SENSOR CONFIGURATION
1. Installation Details
e Installation Details screen allows you to position the sensor relative to the stop bar and
determine the direction of trac to be monitored (see Figure 6.2).
Direction of trac
Stop bar
SmartSensor
Advance
Changes
direction of
trac
Changes
location of
stop bar
Changes
position of
sensor
Height of
sensor
Figure 6.2 – Installation Details Screen
e roadway part of the screen is used to illustrate the sensor’s position relative to the stop
bar; the controls on the right side of the screen allow you to specify the direction of trac
to be monitored and the sensor’s position. e distance units are displayed in the bottom-
right corner of the screen.
e OK button saves the settings to the sensor; the Undo button restores the settings to the
screen’s initial values; and the Cancel button closes the screen without saving changes to
the sensor.
Changing the Trac Direction
e SmartSensor Advance can be congured to detect trac moving towards or away from
the sensor, but will not detect stationary vehicles.
e arrow displayed on the roadway represents the direction of trac ow being detected
by the sensor. Click the Trac button to change the monitored trac direction. e direc-
tion of the arrow displayed on the button shows the direction that will be selected if the
button is clicked, and always points in the opposite direction as the arrow on the roadway.
Positioning the Stop Bar
e ability to move the stop bar up and down the display adds exibility in representing the
relative location of the sensor to the stop bar and the direction of trac ow. e location
of the stop bar is always represented as a distance of zero (the sensor range is relative to the
stop bar).
Position the stop bar by clicking on the stop bar or its label and dragging it anywhere on the
- SmartSensor Advance 1
- SmartSensor 2
- Contents 4
- Introduction 6
- SmartSensor Advance Package 7
- Selecting a Detection Method 7
- Selecting a Mounting Location 8
- Installing the SmartSensor 14
- Selecting the Mounting Height 16
- Mounting the Sensor 17
- Distance 18
- Oset (perpendicular) 18
- Aligning the Sensor 20
- Figure 1.9 – Viewpoint 1 21
- Using the Viewfinder 22
- To target 23
- Figure 1.12 – Viewpoint 1 23
- Grounding the Sensor 26
- Connecting Power and 28
- Surge Protection 2 28
- Mounting the Backplate 29
- Connecting AC Power 29
- Push this button to 32
- (see Figure 2.8) 35
- Contact Closure Connections 37
- Using SmartSensor Manager 38
- Advance 3 40
- Figure 3.3 – Shortcut Options 42
- Communication 4 44
- Serial Connection 45
- Internet Connection 46
- Virtual Connection 47
- Virtual Sensor File 48
- Selecting a Tracker Log File 49
- Multi-drop Network 50
- Address Book 51
- Check Hardware 53
- Communication Error Log 54
- Sensor Settings 5 58
- Figure 5.2 – General Tab 59
- Communication Tab 60
- Sensor Configuration 6 62
- 1. Installation Details 63
- Positioning the Sensor 64
- 3. Manual Radar Adjustment 66
- Editing Sensitivity 67
- Changing the PGA 70
- Channels-Alerts-Zones 7 72
- Channels 73
- Channel 1 74
- Priority Channel 75
- Pulse Channel 78
- Normal Channel 80
- Latched Channel 82
- Enabling an Alert 85
- Logic (OR/AND) 85
- Inverted Zones 85
- Range (ft) 86
- Speed (mph) and ETA (s) 87
- Right Sidebar 93
- (All) Channels 94
- Individual Channel 95
- Channel LED 97
- Zone LED 98
- Alert LED 98
- Roadway Display 99
- Qualified Count 102
- Dynamic Density 103
- Tri-view 104
- Tracker Highlighting 105
- Left Sidebar 107
- Figure 8.24 – Log File 109
- Figure 8.25 – Pulse Log File 109
- In this chapter 110
- Primary Push Manager 111
- Specify output frequency 112
- Secondary Push Manager 113
- Templates 10 116
- Creating a Channel Template 117
- Importing a Channel Template 117
- 118 CHAPTER 10 TEMPLATES 119
- Tools 11 120
- Backup/Restore Tool 121
- Restoring the Configuration 122
- Restoring to Factory Defaults 123
- Beam Alignment Tool 124
- Serial Terminal 125
- Rack Card Tools 126
- Using the Rack Card Tool 127
- Firmware Version 128
- Signal Cards Switch 128
- Channel Outputs Switch 128
- Fail Safe Mode 133
- Rack Card Dip Switch 133
- Click 104 Configuration 135
- Appendix 138
- Creating Custom Cables 139
- Appendix B – Cable Lengths 140
- APPENDIX 143 144
- APPENDIX 145 146
- 146 APPENDIX 147
Produits connexes et manuels pour Capteurs Wavetronix SmartSensor Advance Extended Range (SS-200E) - Use
(78 pages)
(4 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels