Wavetronix SmartSensor Advance Extended Range (SS-200E) - Use Manuel d'utilisateur Page 69
- Page / 148
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
68 CHAPTER 6 SENSOR CONFIGURATION
3 Click the Edit button and the Edit Sensitivity resholds screen will appear (see Figure
6.10). e following three editing modes are available for modifying sensitivity values:
e +/- mode adds or subtracts the specied number to the existing sensitivity lev-
els.
e % mode sets the sensitivity level to be the specied percent of the existing value.
e Value mode sets the sensitivity level to be the specied value.
Figure 6.10 – Edit Sensitivity Thresholds Screen for Advance (left)
and Advance Extended Range (right)
4 Click and drag again to select the exact range bins to adjust.
5 Make the sensitivity level adjustments.
6 Aer adjusting the sensitivity, click the Enter button to apply the adjustment.
7 Click the OK button to accept the modications and close the Edit Sensitivity window;
click the Undo button to return all modied sensitivity levels to their initial values; or
click the Cancel button to undo all changes made.
8 Re-evaluate the detections.
If any changes were made during the Sensor Conguration process, a pop-up window will
appear prompting the user to save the changes to the sensor’s FLASH memory. Changes
that were not written to FLASH will be lost the next time the sensor reboots. e process of
saving to FLASH memory takes approximately ve seconds.
Selecting a Tracker Display Mode
e following is a list of tracker display data that can be changed by clicking the display bar
at the base of the roadway:
Range
Speed
ETA
ID
Blank
Disabled
- SmartSensor Advance 1
- SmartSensor 2
- Contents 4
- Introduction 6
- SmartSensor Advance Package 7
- Selecting a Detection Method 7
- Selecting a Mounting Location 8
- Installing the SmartSensor 14
- Selecting the Mounting Height 16
- Mounting the Sensor 17
- Distance 18
- Oset (perpendicular) 18
- Aligning the Sensor 20
- Figure 1.9 – Viewpoint 1 21
- Using the Viewfinder 22
- To target 23
- Figure 1.12 – Viewpoint 1 23
- Grounding the Sensor 26
- Connecting Power and 28
- Surge Protection 2 28
- Mounting the Backplate 29
- Connecting AC Power 29
- Push this button to 32
- (see Figure 2.8) 35
- Contact Closure Connections 37
- Using SmartSensor Manager 38
- Advance 3 40
- Figure 3.3 – Shortcut Options 42
- Communication 4 44
- Serial Connection 45
- Internet Connection 46
- Virtual Connection 47
- Virtual Sensor File 48
- Selecting a Tracker Log File 49
- Multi-drop Network 50
- Address Book 51
- Check Hardware 53
- Communication Error Log 54
- Sensor Settings 5 58
- Figure 5.2 – General Tab 59
- Communication Tab 60
- Sensor Configuration 6 62
- 1. Installation Details 63
- Positioning the Sensor 64
- 3. Manual Radar Adjustment 66
- Editing Sensitivity 67
- Changing the PGA 70
- Channels-Alerts-Zones 7 72
- Channels 73
- Channel 1 74
- Priority Channel 75
- Pulse Channel 78
- Normal Channel 80
- Latched Channel 82
- Enabling an Alert 85
- Logic (OR/AND) 85
- Inverted Zones 85
- Range (ft) 86
- Speed (mph) and ETA (s) 87
- Right Sidebar 93
- (All) Channels 94
- Individual Channel 95
- Channel LED 97
- Zone LED 98
- Alert LED 98
- Roadway Display 99
- Qualified Count 102
- Dynamic Density 103
- Tri-view 104
- Tracker Highlighting 105
- Left Sidebar 107
- Figure 8.24 – Log File 109
- Figure 8.25 – Pulse Log File 109
- In this chapter 110
- Primary Push Manager 111
- Specify output frequency 112
- Secondary Push Manager 113
- Templates 10 116
- Creating a Channel Template 117
- Importing a Channel Template 117
- 118 CHAPTER 10 TEMPLATES 119
- Tools 11 120
- Backup/Restore Tool 121
- Restoring the Configuration 122
- Restoring to Factory Defaults 123
- Beam Alignment Tool 124
- Serial Terminal 125
- Rack Card Tools 126
- Using the Rack Card Tool 127
- Firmware Version 128
- Signal Cards Switch 128
- Channel Outputs Switch 128
- Fail Safe Mode 133
- Rack Card Dip Switch 133
- Click 104 Configuration 135
- Appendix 138
- Creating Custom Cables 139
- Appendix B – Cable Lengths 140
- APPENDIX 143 144
- APPENDIX 145 146
- 146 APPENDIX 147
Produits connexes et manuels pour Capteurs Wavetronix SmartSensor Advance Extended Range (SS-200E) - Use
(78 pages)
(4 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.030 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels